®
JBL CINEMA SOUND
SPEAKERS
CS400SAT
OWNER’S GUIDE
THANK YOU FOR CHOOSING JBL
For more than 60 years, JBL has been involved in every aspect of
music and film recording and reproduction, from live performances
to the recordings you play in your home, car or office.
Subwoofer
Right Front
Channel
We’re confident that the JBL speakers you have chosen will provide
every note of enjoyment that you expected – and that when you think
about purchasing additional audio equipment for your home, car or
office, you will once again choose JBL.
Center
Channel
Right
Surround
Channel
Left Front
Channel
Please take a moment to register your product on our Web site at
www.jbl.com. It enables us to keep you posted on our latest advance-
ments, and helps us to better understand our customers and build
products that meet their needs and expectations.
Right Rear
Channel
INCLUDED
Carefully unpack the system. If you suspect damage from transit, report
it immediately to your dealer and/or delivery service. Keep the shipping
carton and packing materials for future use. Open the package and verify
the following contents:
Left
Surround
Channel
Left Rear
Channel
Figure 2. This figure shows an alternative layout, which may be
more suitable for some rooms.
PLACEMENT
wall
(2) Speakers
(2) Adjustable
brackets with
tightening bar
(2) Fixed wall
brackets
NOTE: The CS400SAT can be placed directly on a shelf, or mounted on
a wall using the included wall brackets.
As Left and Right Front Channels
For left and right front channels, place one satellite to the left
and another to the right of the television, as shown in Figure 1.
Since the speakers are magnetically shielded, you can place them
very close to the TV without worrying about the magnetic field
distorting the picture.
PLANNING YOUR SYSTEM
Before deciding where to best place your speakers, survey your
room and study Figures 1 and 2.
Subwoofer
As Surround Channels
For left and right surround channels, place one speaker on the left
and another on the right, to the side of or slightly behind the listening
area. The surround speakers should be mounted at a height of
between 5 ft. (1.5m) and 7 ft. (2m).
Left Front
Channel
Center
Channel
Right Front
Channel
In 7-channel configurations, place the rear channel(s) behind
the listening position, as shown in Figures 1 and 2.
NOTE: A powered subwoofer will add impact and realism to
both music and film soundtracks. Contact your JBL dealer for
recommendations on subwoofer models for your application.
Couch
Mounting on Floor Stands
An optional floor stand is available, should you prefer to place
your CS400SAT satellites on the floor; see your dealer or visit
Left Rear
Channel
Right Rear
Channel
Left
Surround
Channel
Right
Surround
Channel
Figure 1. In this overhead view of a typical installation, satellite
speakers are used to reproduce sound for the front and surround
channels. The center channel reproduces sound and dialogue.
The powered subwoofer provides bass for effects and music.
3
WALL-MOUNTING THE SATELLITES
The CS400SAT is designed to be mounted on the wall. There is a
fixed-mount wall bracket and an adjustable wall bracket provided for
each satellite. Each speaker bracket will require up to four 1-1/2"#10
wood screws; each screw should be fastened to a wall stud. If a wall
stud is unavailable, install an anchor appropriate for a 1-1/2"#10 screw.
Step 4. Unscrew round collar (C) from bracket (A).
A
C
B
NOTE: The customer is responsible for the correct selection
and use of mounting hardware (available through hardware stores)
that will ensure the proper and safe wall-mounting of the speakers.
Step 5. Screw the ball and shaft assembly (B) to the 1/4"-20 insert
on the back of the satellite (do not use the bottom insert on the
speaker). Back out 1/2 of a turn and tighten the nut against the
speaker. If the ball and shaft assembly is not backed out before
tightening the nut, performing Step 8 below may dislodge the
threaded insert in the speaker housing and permanently damage
the speaker.
Fixed-Mount Wall Bracket
Step 1. Mark the positions on the wall where you would like
to place the mounting screws.
Step 2. Attach the bracket to the wall using two screws
(not included).
Step 3. Remove the rubber ring on the bottom of the satellite,
and sit the satellite onto the back bracket.
Step 4. Attach 1/4-20 screw into insert on bottom of speaker
and tighten.
Step 6. Attach speaker wire as shown on page 5.
Step 7. Drop round collar (C) over ball and shaft assembly (B) that
is mounted to the speaker with the finished side of the collar facing
the rear of the speaker.
Step 8. Carefully push the ball straight into the socket mounted on
the wall, angle the speaker as desired and tighten the collar using
the enclosed metal bar.
Metal bar
Adjustable Wall Bracket
Step 1. Remove cap over threaded insert on rear of speaker
Step 2. Mark the positions on the wall where you would like to place
the mounting screws.
Figure 3. Bracket on wall.
Step 3. Place bracket against the wall and fasten four 1-1/2" #10
wood screws through the bracket’s screw holes into the wall. If a
wall stud is not available, use an appropriate anchor.
4
CONNECTIONS
MAINTENANCE AND SERVICE
After placing the speakers, you are ready to connect your system.
First, turn off all audio-system power. Use high-quality speaker wire
to make your connections; #18-gauge speaker wire with polarity cod-
ing is recommended. For longer distances, #16-gauge or heavier wire
is recommended. The side of the wire with a ridge or other coding is
usually considered positive polarity (i.e., +). Also, consult the owner’s
manuals that were included with your amplifier or receiver to confirm
connection procedures. Observe polarities when making speaker
connections, as shown in Figure 4. Connect each + terminal on the
back of the amplifier or receiver to the respective + (red) terminal on
each speaker. Connect the – (black) terminals in the same way.
The enclosure may be cleaned using a soft cloth to remove finger-
prints or to wipe off dust.
All wiring connections should be inspected and cleaned or remade
periodically. The frequency of maintenance depends on the metals
involved in the connections, atmospheric conditions and other fac-
tors, but once per year is the minimum.
If a problem occurs, make sure that all connections are properly
made and clean. If a problem exists in one loudspeaker, reverse the
connection wires to the left and right system. If the problem remains
in the same speaker, then the fault is with the loudspeaker. If the
problem appears in the opposite speaker, the cause is in another
component or cable. In the event that your speaker ever needs
service, contact your local JBL dealer or distributor, or visit
Important!
Do not reverse polarities (i.e., + to –, or – to +) when making
connections. Doing so will cause poor imaging and diminished
bass response. Be certain that positive and negative wire strands
are completely isolated to avoid short circuits that may damage your
equipment.
NOTE: On certain models using hexagonal terminal nuts, a small
socket wrench is provided to help in properly tightening the terminals.
Hand-tighten only and do not overtighten.
Figure 4. Wiring diagram shows polarity connections
for one channel of a home theater system.
5
SPECIFICATIONS
CS400SAT
Frequency Range (–6dB):
110Hz – 20,000Hz
Recommended
Amplifier Power Range:
10 – 100 Watts
Sensitivity (2.83V @ 1 meter)
Nominal Impedance:
Crossover Frequency:
Midrange Driver:
86dB
8Ω
3.0kHz; 12dB/octave
3-1/2" (89mm) Magnetically shielded
1/2" (13mm) Titanium-laminate, magnetically shielded
6" x 6-3/8" x 3-7/8" (152mm x 162mm x 98mm)
2.0 lb (0.9kg)
High-Frequency Driver:
Dimensions (H x W x D):
Weight:
Features, specifications and appearance are subject to change without notice.
Declaration of Conformity
We, Harman Consumer Group International
2, route de Tours
72500 Château du Loir
France
declare in own responsibility that the product described
in this owner’s manual is in compliance with technical
standards:
EN 61000-6-3:2001
EN 61000-6-1:2001
Laurent Rault
Harman Consumer Group International
Château du Loir, France 11/06
6
JBL is a trademark of Harman International Industries, Incorporated, registered in
the United States and/or other countries. Pro Sound Comes Home is a trademark
of Harman International Industries, Incorporated.
™
PRO SOUND COMES HOME
Harman Consumer Group, Inc., 250 Crossways Park Drive, Woodbury, NY 11797 USA
8500 Balboa Boulevard, Northridge, CA 91329 USA
2, route de Tours, 72500 Château du Loir, France
© 2006 Harman International Industries, Incorporated. All rights reserved.
Part No. 406-000-05544-E
|